CENTRIFUGAL PUMPS
SUMMIT 2196
2196 ANSI / General Purpose Chemical Pump
Features
-
Rear Pull-Out Design
-
Efficient Interchangeable Parts
-
Capacities to 6000 GPM
-
Heads to 730 feet
-
Temperatures to 700 deg F
-
Fully Open Impeller
-
Extra Large Oil Sump
-
Rigid Frame Foot
Applications
Water, Chemical, Oil, Pulp, and Paper, General Purpose Pump
Optional Features
-
Finned-Tube Oil Cooler
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
2196FF / All 316 Stainless Steel
Increase the Longevity of your pump and reduce your total cost of ownership
Features
-
Available as a power end, shaft kit or complete pump
-
Interchangeable with 2196 ANSI, 2196R, 2196LF and 2796
-
316 Stainless Steel Fasteners, plugs, sight glass and frame foot
-
High Quality SKF® Bearings
-
Thermal expansion stresses are reduced
Benefits
-
Advanced thermal fatigue resistance
-
Extended product life cycle
-
Thermal expansion stresses are reduced
-
Extended MTBF (Mean Time Before Failure)
Applications
Corrosive Services, Acid & Caustics, Pharmaceuticals, Food & Beverage, Hot Oils, Chemical/Petrochemical Processing
Optional Features
-
Finned-Tube Oil Cooler
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
SUMMIT 2196FF
SUMMIT 2196R
2196 R ANSI / Recessed Pump
Features
Utilizes your existing 2196 power end and ANSI bolt pattern
-
Handles fibrous and shear sensitive materials
-
Minimizes degradation of solids
-
Available in 5 different sizes and a variety of materials
Applications
Paper & Pulp, Cleaners, Manure Transfer, Waste Water, Fruit Pulp
Optional Features
-
Finned-Tube Oil Cooler
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
SUMMIT 2196LF
2196LF ANSI / Low Flow Pump
Features
-
Low Flow High Head Applications
-
Radial Vane Impeller
-
Balance Holes on Impeller
-
Interchangeability with Existing ANSI Pump
-
Rigid Frame Foot
Benefits
-
Reduced Shaft Vibration
-
Lower NPSHr
-
Lower Seal Chamber Pressure
-
Extended MTBF on Pump and Mechanical Seal
Applications
Additive Chemicals, Batch/Continuous Chemical Reactors, Chemical Dryers, Chemical Processes, Condensate Service, Evaporators, Petro Chemical Service, Shower Services
Optional Features
-
Finned-Tube Oil Cooler
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
SUMMIT CLARK 3
Clark 3 ANSI / General Purpose Pump
Features
-
Conforms to ASME B73.1M (ANSI)
-
Capacities to 5,000 GPM
-
Head to 740 Feet
-
Back Pull Out Design
-
Threaded Bearing Housing
-
Accurate Impeller Adjustments
-
Reverse Vane Closed Impeller
-
Reduced Shaft Deflection
Applications
Water, Chemical, Oil, Pulp and Paper, General Purpose Pump
Optional Features
-
Multiple Rear Cover Options
-
Open Impeller Design Available
-
Finned Tube Oil Cooler
SUMMIT 2796
2796 / Self Priming Process Pump
Features
-
Self-Priming
-
Utilizes Existing 2196 Power End
-
Rear Pull-Out Design
-
External Axial Impeller Adjustment
-
Open Non-Clogging Impeller
-
ANSI Foot Pattern
-
Extra Large Oil Sump
-
Rigid Frame Foot
Applications
Bilge Water Removal, Industrial Sump, Chemical Transfer, Mine De-watering, Filter Systems
Optional Features
-
Finned-Tube Oil Cooler
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
SUMMIT 2175
2175 / Heavy Duty Process Pump
Features
-
Rear Pull-Out Design
-
Efficient Interchangeable Parts
-
Sacrificial Wear Items
-
Double Wall Volute on Larger Sizes
Applications
Pulp & Paper:
Cleaners, Filtrate, Liquor, Screen Reject
Steel:
Cooling Water, Descaling, Slurries, Tailings
Food:
Beet and Cane Sugar, Cane Juices, Fruit Pulp, Wet Corn Millings
General:
Manure Transfer, Mine Water, Waste Treatment
SUMMIT CC & FM
CC & FM / Close Coupled & Frame Mounted
Features
-
Capacities to 2,300 GPM
-
Heads to 440 Feet
-
Use of Minimal Space
-
Interchangeable Parts
-
Split Casing Design
-
Sacrificial Sleeves and Rings
Applications
-
Clean Water
-
Solvents
-
Light Oils
-
Non-Corrosive Chemicals
-
Coolants
-
Brines
Parts
CC and FM pumps and parts manufactured by Summit Pump, Inc. are functionally and dimensionally interchangeable with the Peerless C & F line manufactured by Peerless Pump. Parts for part interchangeability means you have a quality option when sourcing pumps or parts.
SUMMIT DSR / SPLIT CASE
DSR / Double Suction Pump
Features
-
Capacities to 6,000 GPM
-
Heads to 430 Feet
-
Horizontal Split Case Design
-
High Efficiency and Low NPSHr
-
Closed Impeller
Applications
Oil and Gas, Cooling Water, Boilers, Sea Water, Mining, Chemical Process, Irrigation, Condensate Pump, Water Supply
Optional Features
-
Replaceable Wear Rings, Variety of Materials
-
Packing or Mechanical Seals
SUMMIT SN / TRASH PUMP
SN / Self-Primer Pump
Features
-
Self-Priming Non-Clogging
-
Capacities to 3,400 GPM
-
Hard Faced Mechanical Seals Standard
-
Standard Spool Piece Flanges
-
Direct Drive or V-Belt
-
Designed for Easy Maintenance
-
Compact Removable Rotating Assembly
Applications
Sump or Bilge Pump, Mild Corrosives, Sewage, Pulp & Paper, Wineries, Fibrous Materials
Optional Features/Versions
-
SN B: Utilizes 5 Vane Impeller
SUMMIT SP / SLURRY PUMP
SP Slurry / Slurry Pump
Features
-
Heavy Duty Pumps
-
Designed for Abrasive Applications
-
High Chrome or Removable Rubber Wear Parts
-
Packed Box Standard
-
External Impeller Adjustment
-
Capacities to 7,000 GPM
-
Heads to 240 Feet
Applications
Waste Sludge, Paper Pulp & Wastes, Clay & Sand Slurries, Lime Mud, Dirty Water
SUMMIT IN-LINE PROCESS PUMP
2996
Features
-
In-Line (IL) Process Pump
-
High Tolerance Fits for Accurate Alignment
-
Open Impeller
-
External Impeller Adjustment
-
Back Pull-Out Integrated
-
Flexible Coupling Options
-
Temperatures to 500°F
-
Capacities to 1,400 Gpm
-
Heads to 190 Feet
Applications
Water, Chemical, Oil, Pulp, and Paper, In-Line Process Pump
Optional Features
-
Multiple Stuffing Box Cover Options
-
Standard Bore
-
Large Bore
-
Taper Bore
-
API MAXUM OH2
API 610 Compliant End-Suction Pump
This model is fully compliant with latest edition API 610 specifications. Standard features include renewable casing wear rings, API 610 seal chamber sized to accommodate 682 mechanical seals, back pull-out construction, dynamically-balanced impellers, heavy-duty carbon steel/finned bearing housing equipped with labyrinth-type oil seals, and fan cooling. Locations are also included for temperature probes, as standard. Common options include single, double or tandem mechanical seals, and various seal flush systems. Heavy-duty baseplates, casing jackets, and various levels of performance testing are also available.
​
-
Flows to 11,500 US GPM
-
Heads to 720 FT
-
Efficiencies to 88%
-
Power to 900 HP
-
Speeds up to 3,550 RPM
-
Temperatures to 600°F
​
APPLICATIONS
MAXUM OH1
Heavy-Duty, Horizontal End-Suction Pump
Designed as a foot-mounted version of our API centerline-mounted Maxum OH2, the Maxum OH1 is an industry workhorse. The Maxum OH1 can be motor, engine, or turbine-driven and is ideal for water, hydrocarbons, caustic and acid applications. With hydraulic performance to 11,000 GPM and 720 feet of head, this pump family is available in carbon steel, 12% chrome, 316L and duplex stainless steel, according to standard API material codes. In addition to these, higher alloys such as Alloy 20, Hastelloy B or C, Monel and titanium are also available.
​
-
Flows to 11,500 US GPM
-
Heads to 720 FT
-
Efficiencies to 88%
-
Power to 900 HP
-
Speeds up to 3,550 RPM
-
Temperatures to 300°F
​
APPLICATIONS
RS
Multistage, Ring Section Pump
The RS is offered with Class 300 ANSI R.F. inlet flanges and Class 600 or 900 ANSI R.F. discharge flanges, depending on the pressures and number of stages involved. Hydraulic performance extends to 2,000 GPM and 3,400 ft. TDH, making it ideally suited for the most demanding industrial and process applications.
The RS design incorporates a product-lubricated, advanced composite material, sleeve-type radial bearing at the outboard (discharge) end. The thrust bearings are two matched angular contact ball bearings located at the inboard (suction) end of the pump. An optional outboard mechanical seal with an inboard radial ball bearing is also available. The RS has oil-lubricated ball bearings, which can be water cooled. Larger units can also be fan cooled.
​
-
Flows to 2,000 US GPM
-
Heads to 3,400 FT
-
Pressures to 1,500 PSIG
-
Temperatures from -20° to 300°F
-
Speeds up to 3,550 RPM​
​
APPLICATIONS
GH
End-Suction Centrifugal Pump
Available as either a frame-mounted (GHF) or close-coupled (GHC) unit, the GH is based on the same product platform as our vertical pumps and shares many of the same parts.
For added simplicity, the entire series is covered by only three bearing frames and comes in whole pump or modular kit form. The GHC is fully compatible with standard, off-the-shelf NEMA JP and JM frame motors, and all models feature a back pull-out design and casings rotatable in 90° increments for different field piping orientations.
Other common features for the GH include 316 SS shaft sleeves, keyed impellers to prevent accidental spin off, dynamic balancing to ISO G2.5 guidelines, and regreasable bearings secured with locking rings, as standard. These features combine to produce shaft deflection values so low that they exceed the requirements of ANSI B73.1M-1991 and overall, provide some of the most efficient hydraulics in the industry.
​
-
Flows to 2,500 US GPM
-
Heads to 520 FT
-
Efficiencies to 85%
-
Solids to 1.250"
-
Power to 150 HP
-
Speeds up to 3,550 RPM
​
APPLICATIONS
M SERIES
ASTM F998 Close-Coupled Centrifugal Pump
Conforming to the requirements of ASTM F998, including the Navy supplement, hydraulic performance extends to 5,000 GPM and 713 feet of head. This range is covered by 24 sizes in 316 SS and CD4MCuN duplex SS as the standard materials. Units can be mounted either horizontally or vertically.
Designed to meet Naval Requirements including MIL-S-901 Shock, MIL-STD-167-1 Type I Environmental Vibration, MIL-STD-740-1 Airborne Noise and MIL-STD-740-2 Structureborne Noise. All models are back pull-out designs with replaceable wear rings, encloded impellers and balancing holes with dual volute casings as required. These features combine to produce shaft deflections of less than 0.002″ at shutoff, and overall, offer some of the most efficient hydraulics to be found in a pump of this type anywhere.
​
-
Flows to 5,000 US GPM
-
Heads to 700 FT
-
Efficiencies to 88%
-
Temperatures to 300°F
-
Power to 300 HP
-
Speeds up to 3,550 RPM
​
APPLICATIONS
850
Horizontal Filtrate Pump
Rugged in design and dependable in nature, the 850 is a proven performer in some of the earth’s toughest environments. Capable of operating in vacuum conditions up to 26″ Hg, the 850 is well suited for vacuum filtration and dewatering systems with difficult suction conditions. A vent port allows pumping to resume even after short periods of interrupted flow, assuring continuous pumping, from a trickle to full capacity.
With a semi-open impeller and a variety of material choices ranging from duplex stainless steel to rubber lined, the 850 is ideal for abrasives and light slurry duty in the mining, power generation, and pulp and paper industries.
​
-
Flows to 700 US GPM
-
Heads to 120 FT
-
Temperatures to 250°F
-
Power to 50 HP
-
Speeds up to 2,450 RPM
​
APPLICATIONS
855
Handles up to 26" Hg Vacuum
The 855 was originally developed in the late 1950s at the request of a large Original Equipment Manufacturer (OEM) of vacuum filtration equipment. Mounting the flange directly to the receiver tank eliminates suction piping and minimizes NPSH problems. The design allows pumping to resume even after short periods of interrupted flow. Capable of operating in vacuum conditions up to 26″ Hg, the specially designed semi-open impeller assures pumping from a trickle to full capacity. Rugged in design and dependable in nature, the 855 is a workhorse in some of the toughest environments in the industry.
The 855 features an overhead v-belt drive arrangement as standard, with options for close-coupled units. By utilizing either belt drive or variable frequency drive, performance characteristics can be fine-tuned to match most system requirements. With a simple, vertically-split case design, the 855 may be disassembled to expose the entire wetted area. Standard features include a packed stuffing box with seal water connections provided to ensure lubrication and eliminate vacuum/air leakage. Pumps come with discharge flanges machined for both Class 150 ANSI and DIN PN10 connections.
​
-
Flows to 700 US GPM
-
Heads to 120 FT
-
Temperatures to 250°F
-
Power to 20 HP
-
Speeds up to 2,450 RPM
​
APPLICATIONS
KWP
Non-Clogging Process Pump
The KWP is designed for fluids with entrained solids and fibrous materials up to 1.5″ in diameter. Wide passages in the two-vane enclosed impeller minimize clogging and crushing of the entrained material. Primarily a horizontal unit, the KWP can be either frame-mounted or close-coupled.
Common options include soft packing, single or double cartridge seals, and any type of seal flush plan.
The back pull-out design makes maintenance easy and lower total life cycle cost. Shaft deflections are limited to 0.002″ at the seal.
All together, these features combine to make the KWP a pump of exceptional value, combining affordability with some of the most efficient hydraulics found in a pump of this type.
​
-
Flows to 1,300 US GPM
-
Heads to 240 FT
-
Temperatures to 250°F
-
Power to 50 HP
-
Speeds up to 3,550 RPM
-
Solids to 1-1/2" diameter
​
APPLICATIONS
